Setup of Coredy's Range Extender:

Setup of Coredy's Range Extender:

If you are having difficulties streaming, playing sports, and doing your office job, carry home the brand-new Coredy Range Extender Setup. The wifi range extender increases the signal strength and improves the real wifi signal.

Setup of Coredy's Wi-Fi Range Extender:

• An electronic system that improves and extends your wifi network and eliminates the dead areas of your house from the signal is a wifi range extender.

• It acts as a medium or bridge between the wifi router or access point and the devices that are out of its control. This moves the wifi signal to the dead zones in your home or workplace.

• The signal is received and repeated from the data generation system to the other areas of your home (router, mobile, or computer).

Why do you want the Coredy Extender to be used?

The Coredy extender comes with multi-functional technology and also acts as an extension as well as a router or connection point.

Even in the dead areas of your house, the extender is laced with high technology that allows seamless communication.

Setup of Coredy's Extender:

The extender setup has two steps:

• Powering on the extender

• Connecting the extender to the existing network

• Powering on the extender

Before any further steps are taken, you need to power the extender to allow it to connect to the available networks.

• Switch on the extender by using the power on / off button.

• Set the mode transfer button to 'Repeater' to use the system as a network extender.

• Plug-in the extender to a power source. (If necessary, in the same room where the router is connected.)

Note: The extender should be mounted close to the access point while it is near the access point.

• First time joining up.

• Connecting Coredy to an existing extender network

• The extender can be linked to an existing network in two ways:

Using WPS

On the internet using a browser

Coredy setup Extender Connect Coredy to a web browser

• Open the wi-fi network manager app on your mobile device or computer and check for the extension name by default, i.e. 'Coredy .'

• Click the name of the extender and enter your mobile device or computer's pin or password to connect to

• (The password or pin is written on the extension's back panel.)

• Open the web browser of your computer and check for enter the 192.168.10.1 IP address in the address bar.

• If required, login to the admin page by entering 'admin' as both username and password (both are minuscule).

• Go to the mode wizard and choose the choice for the repeater.

• To select the network to be extended, click on the select button.

• When the network list is not properly configured, refresh the list. In the space, enter the password or pin for the current network.

• Click Submit and wait for the extender to restart for a few minutes.

Look for, and connect to, the extended network.(You must enter the same password you entered when connecting to the Extender).

The extended wifi network's new name is 'Coredy Ext' by design.

Note: If there is no connection to the new wifi network, the WLAN LED will keep blinking and the name of the new network will not be changed.

Unplug and switch the extender to about halfway between the poor zones or dead zones of your house and the router.

Note: Make sure that all three WLAN LED lamps are amber at the same time (this indicates an appropriate position for the extender region).

Tip: Position the extender in a higher region so that it has minimum obstacles including walls, ceilings, and windows.

Coredy Extender setup via WPS:

In order to make it simpler and easier to connect to a secure and secured wireless network from a computer or other devices, the Wi-fi Safe Setup (WPS) comes with most routers and repeaters.

The WPS setup makes it possible to connect to a wireless network without entering a username and password.

Various manufacturers use distinct terminology for the WPS button:

Link & Drive

Simple Wifi Setup

PBC-PBC

Fast Stable setup (QSS)

The following are the steps for using the WPS button to connect to a wireless network:

• Click the WPS button located on the extender's front panel. (The WPS-led will blink after being switched on.

• Wait 1-2 minutes and push either the router's WPS button or the access point.t.

• The network name will automatically change to 'Coredy Ext' after a good link. Also, the WLAN-1 LED will turn amber, too.

• Confirm your connection via your computer or wifi system

• Unplug and transfer the extensor between the halfway point of the extension

• The router/access point and vulnerable zones / dead areas of your house or office.

• In a higher, elevated position, place the extension that allows for a minimum of obstacles such as walls, windows.