How We Research
We compare products from their published specs and features; the verdicts below are our independent editorial opinions.
Updated: 2026-10-07 · 6 min read · Independent comparison
• BUTIAO 40mm — biggest strength: Broad, explicitly listed compatibility with Logitech G733/G933/G633/G533/G433/G430/G233, Technics EAH-DJ1200, Marshall Major/Monitor models, and Turtle Beach Stealth 500 / Recon 50.
• BUTIAO 40mm — biggest trade-off: It's a raw component, not a finished headphone, and the listing warns you to keep soldering under three seconds or you risk burning the voice coil.
• Rillpac 1 — biggest strength: A 40mm full-range titanium driver with a stated 10Hz–27kHz frequency response, 32Ω impedance, 97dB/mW sensitivity and 1000mW max input, plus a front cover included.
• Rillpac 1 — biggest trade-off: It's positioned as an Onkyo ES-FC300 replacement, and if you want to build your own housing you have to disassemble the speaker from its plastic cover yourself.
• Who BUTIAO 40mm is for: Anyone reviving a broken gaming headset who wants the simplest path back to working audio.
• Who Rillpac 1 is for: Tinkerers chasing a music-focused titanium driver who don't mind a more hands-on install.
The BUTIAO 40mm is a repair-and-replace part first, and that's exactly how you should judge it. It ships as two 40mm speaker units at 32ohm, with a plastic enclosure and a black finish. The headline feature is compatibility: this driver is listed as compatible with a spread of Logitech gaming headsets, the Technics EAH-DJ1200, several Marshall Major/Monitor models, and Turtle Beach Stealth 500 and Recon 50. If your current headset died on one side and you liked everything else about it, that list is the whole argument.
Sound-wise, the sheet describes a high-quality sound film with clear, pure high frequencies and low-pitched sound. That's a sensible tuning for spoken-word content — webinars, meetings, lectures — where you want voices intelligible and a bit of body underneath them rather than a thumping, boomy low end that smears speech.
The catch is the install. This is a soldered component with polarity to respect: the positive pole is marked with a small colored dot, and the unmarked point is negative. BUTIAO explicitly warns not to solder for more than three seconds, because too much heat can burn the voice coil lead or the board and leave you with a dead, shorted speaker. So: buy this if you're repairing a listed headset and you (or a friend) can handle a quick, careful solder joint. Skip it if you want a plug-and-play finished product or you've never held an iron — the failure mode here is destroying the very part you just bought.
The Rillpac 1 is the more ambitious of the two, and it's aimed at a different person entirely. It's sold as a pair of 32ohm 40mm replacement drivers for the Onkyo ES-FC300, and the spec sheet is genuinely more detailed: dynamic titanium drivers, 40mm diameter, 97dB/mW output sound pressure level, 10Hz–27kHz frequency response, and 1000mW maximum input power. Those numbers describe a driver built to cover a very wide spectrum rather than just get you back online.
The tuning story is the interesting part. The sheet frames the bass philosophy directly: it's not about quantity but quality, and specifically not "boomy" bass that blurs the audio image. Instead, dual chambers behind the driver are used to control low frequencies and add weight and dynamism. The drivers are described as crisp and detailed in the mid-to-high ranges, sympathetic to compressed audio formats, and sensitive enough for lossless and 192/24 playback. For music, that's a coherent, deliberate design.
There's a practical wrinkle. The listing notes the speaker includes the original front cover, and that if you want to DIY your own headphone housing you'll need to disassemble the speaker from its plastic cover yourself. It also recommends asking a professional repair shop if you can't manage the fix. It's a 2-count package with a stated three-month warranty.
So buy the Rillpac 1 if you're repairing an ES-FC300, or if you're a DIY builder who wants a titanium 40mm driver with a wide stated frequency response and you're fine doing disassembly work. Skip it if you want the widest possible model compatibility out of the box — that's not what this one is selling.
Side-by-Side: Which Should You Choose?
• Best for music-first listening → Rillpac 1. Titanium drivers with a stated 10Hz–27kHz response and dual-chamber bass tuning are aimed squarely at music.
• Best for clarity on spoken-word content like webinars and calls → BUTIAO 40mm. Its described tuning (clear highs, low-pitched body) suits voices, and it's the easier drop-in for the headsets most people already own.
• Best for DIY builders and tinkerers → Rillpac 1. More detailed specs to work from, plus a front cover included.
• Best for lowest install risk → BUTIAO 40mm. Fewer steps, no disassembly of the driver from a cover required.
• Best for replacing a broken Onkyo ES-FC300 driver → Rillpac 1. That's the model it's explicitly built for.
• Best for maximum power headroom → Rillpac 1. Its 1000mW maximum input power is stated right on the sheet.
• Best if you've never soldered → neither, honestly. Both are raw components; BUTIAO's three-second soldering warning makes that plain.
For most people reading this — especially anyone who spends their day in webinars and just wants their headset working again — I'd buy the BUTIAO 40mm. In my opinion, the compatibility list does the heavy lifting: if you own one of the listed Logitech, Marshall, Technics or Turtle Beach models, you already know these drivers are meant for your frame, and the described tuning suits voice-heavy content. I'd pick the Rillpac 1 only if I were repairing an ES-FC300 or deliberately building a music-focused DIY pair and wanted that titanium driver and its wider stated frequency range. Neither is a finished headphone, so factor in whether you can solder before you commit — and check the current price on Amazon before deciding, since that's the one number that changes.
what is 40mm driver in headphones
It's the diameter of the speaker driver inside the earcup — 40 millimeters across the moving diaphragm. Both products here are 40mm drivers rated at 32ohm, but they're sold as replacement parts, not complete headphones.
what are 40mm drivers in headphones
They're the electro-mechanical speakers that convert electrical signal into sound. The BUTIAO 40mm uses a high-quality sound film tuned for clear highs and low-pitched sound, while the Rillpac 1 uses a 40mm full-range titanium driver with a stated 10Hz–27kHz frequency response.
which driver is best for headphones
There's no single "best" size — it depends on tuning and housing. For spoken-word content like webinars, the BUTIAO 40mm's described clarity in the highs and low-pitched body is a sensible fit; for music, the Rillpac 1's titanium driver and dual-chamber bass tuning are the more deliberate design.
is 40mm driver good for headphones
Yes — 40mm is a common, well-rounded size that balances bass presence with clear mids and highs. Both of these are 32ohm 40mm units, so they're reasonable for the models listed in each sheet, provided you can handle the soldering and install.
As an Amazon Associate I earn from qualifying purchases.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon and affiliated sites.
When you buy through links on this page, we may earn a commission from qualifying purchases at no extra cost to you.
Amazon and the Amazon logo are trademarks of Amazon or its affiliates. This site is an independent third-party review and is not affiliated with, endorsed by, or sponsored by Amazon or the product brands mentioned.
See also: YUEBAITU Long Cord vs SNOWSKY FIIO Nature Closed-Back, our OTL Technologies CB1220 vs realme Buds T200 pick, dreamGEAR Universal Elite Amplified vs VCOM RGB Gaming Headphones, ThinkWrite Technologies TWT Audio Ergo vs RUNOLIM Active Noise Cancell