Cable television is a system of delivering television programming to consumers via radio frequency (RF) signals transmitted through coaxial cables, or in more recent systems, light pulses through fibre-optic cables. This contrasts with broadcast television (also known as terrestrial television), in which the television signal is transmitted over-the-air by radio waves and received by a television antenna attached to the television; or satellite television, in which the television signal is transmitted over-the-air by radio waves from a communications satellite orbiting the Earth, and received by a satellite dish antenna on the roof. FM radio programming, high-speed Internet, telephone services, and similar non-television services may also be provided through these cables. Analog television was standard in the 20th century, but since the 2000s, cable systems have been upgraded to digital cable operation.
A cable channel (sometimes known as a cable network) is a television network available via cable television. Many of the same channels are distributed through satellite television. Alternative terms include non-broadcast channel or programming service, the latter being mainly used in legal contexts. The abbreviation CATV is used in the US for cable television and originally stood for community antenna television, from cable television's origins in 1948; in areas where over-the-air TV reception was limited by distance from transmitters or mountainous terrain, large community antennas were constructed, and cable was run from them to individual homes.
Av Broadcast System For Cable Tv 6.0 Crack Free Download
Download 🔥 https://ssurll.com/2xYcKY 🔥
To receive cable television at a given location, cable distribution lines must be available on the local utility poles or underground utility lines. Coaxial cable brings the signal to the customer's building through a service drop, an overhead or underground cable. If the subscriber's building does not have a cable service drop, the cable company will install one. The standard cable used in the U.S. is RG-6, which has a 75 ohm impedance, and connects with a type F connector. The cable company's portion of the wiring usually ends at a distribution box on the building exterior, and built-in cable wiring in the walls usually distributes the signal to jacks in different rooms to which televisions are connected. Multiple cables to different rooms are split off the incoming cable with a small device called a splitter. There are two standards for cable television; older analog cable, and newer digital cable which can carry data signals used by digital television receivers such as high-definition television (HDTV) equipment. All cable companies in the United States have switched to or are in the course of switching to digital cable television since it was first introduced in the late 1990s.
Most cable companies require a set-top box (cable converter box) or a slot on one's TV set for conditional access module cards[2] to view their cable channels, even on newer televisions with digital cable QAM tuners, because most digital cable channels are now encrypted, or scrambled, to reduce cable service theft. A cable from the jack in the wall is attached to the input of the box, and an output cable from the box is attached to the television, usually the RF-IN or composite input on older TVs. Since the set-top box only decodes the single channel that is being watched, each television in the house requires a separate box. Some unencrypted channels, usually traditional over-the-air broadcast networks, can be displayed without a receiver box.[3] The cable company will provide set-top boxes based on the level of service a customer purchases, from basic set-top boxes with a standard-definition picture connected through the standard coaxial connection on the TV, to high-definition wireless digital video recorder (DVR) receivers connected via HDMI or component. Older analog television sets are cable ready and can receive the old analog cable without a set-top box. To receive digital cable channels on an analog television set, even unencrypted ones, requires a different type of box, a digital television adapter supplied by the cable company or purchased by the subscriber. Another new distribution method that takes advantage of the low cost high quality DVB distribution to residential areas, uses TV gateways to convert the DVB-C, DVB-C2 stream to IP for distribution of TV over IP network in the home. Many cable companies offer internet access through DOCSIS.[4]
In the most common system, multiple television channels (as many as 500, although this varies depending on the provider's available channel capacity) are distributed to subscriber residences through a coaxial cable, which comes from a trunkline supported on utility poles originating at the cable company's local distribution facility, called the headend. Many channels can be transmitted through one coaxial cable by a technique called frequency division multiplexing. At the headend, each television channel is translated to a different frequency. By giving each channel a different frequency slot on the cable, the separate television signals do not interfere with each other. At an outdoor cable box on the subscriber's residence, the company's service drop cable is connected to cables distributing the signal to different rooms in the building. At each television, the subscriber's television or a set-top box provided by the cable company translates the desired channel back to its original frequency (baseband), and it is displayed onscreen. Due to widespread cable theft in earlier analog systems, the signals are typically encrypted on modern digital cable systems, and the set-top box must be activated by an activation code sent by the cable company before it will function, which is only sent after the subscriber signs up. If the subscriber fails to pay their bill, the cable company can send a signal to deactivate the subscriber's box, preventing reception.
There are also usually upstream channels on the cable to send data from the customer box to the cable headend, for advanced features such as requesting pay-per-view shows or movies, cable internet access, and cable telephone service. The downstream channels occupy a band of frequencies from approximately 50 MHz to 1 GHz, while the upstream channels occupy frequencies of 5 to 42 MHz. Subscribers pay with a monthly fee. Subscribers can choose from several levels of service, with premium packages including more channels but costing a higher rate. At the local headend, the feed signals from the individual television channels are received by dish antennas from communication satellites. Additional local channels, such as local broadcast television stations, educational channels from local colleges, and community access channels devoted to local governments (PEG channels) are usually included on the cable service. Commercial advertisements for local business are also inserted in the programming at the headend (the individual channels, which are distributed nationally, also have their own nationally oriented commercials).
Modern cable systems are large, with a single network and headend often serving an entire metropolitan area. Most systems use hybrid fiber-coaxial (HFC) distribution; this means the trunklines that carry the signal from the headend to local neighborhoods are optical fiber to provide greater bandwidth and also extra capacity for future expansion. At the headend, the electrical signal is translated into an optical signal and sent through the fiber. The fiber trunkline goes to several distribution hubs, from which multiple fibers fan out to carry the signal to boxes called optical nodes in local communities. At the optical node, the optical signal is translated back into an electrical signal and carried by coaxial cable distribution lines on utility poles, from which cables branch out to a series of signal amplifiers and line extenders. These devices carry the signal to customers via passive RF devices called taps.
The very first cable networks were operated locally, notably in 1936 in London in the United Kingdom[5] and the same year in Berlin in Germany, notably for the Olympic Games, and from 1948 onwards in the United States and Switzerland. This type of local cable network was mainly used to relay terrestrial channels in geographical areas poorly served by terrestrial television signals.[6]
The early systems simply received weak (broadcast) channels, amplified them, and sent them over unshielded wires to the subscribers, limited to a community or to adjacent communities. The receiving antenna would be taller than any individual subscriber could afford, thus bringing in stronger signals; in hilly or mountainous terrain it would be placed at a high elevation.
At the outset, cable systems only served smaller communities without television stations of their own, and which could not easily receive signals from stations in cities because of distance or hilly terrain. In Canada, however, communities with their own signals were fertile cable markets, as viewers wanted to receive American signals. Rarely, as in the college town of Alfred, New York, U.S. cable systems retransmitted Canadian channels.
As equipment improved, all twelve channels could be utilized, except where a local VHF television station broadcast. Local broadcast channels were not usable for signals deemed to be a priority, but technology allowed low-priority signals to be placed on such channels by synchronizing their blanking intervals. TVs were unable to reconcile these blanking intervals and the slight changes due to travel through a medium, causing ghosting. The bandwidth of the amplifiers also was limited, meaning frequencies over 250 MHz were difficult to transmit to distant portions of the coaxial network, and UHF channels could not be used at all. To expand beyond 12 channels, non-standard midband channels had to be used, located between the FM band and Channel 7, or superband beyond Channel 13 up to about 300 MHz; these channels initially were only accessible using separate tuner boxes that sent the chosen channel into the TV set on Channel 2, 3 or 4.[citation needed] Initially, UHF broadcast stations were at a disadvantage because the standard TV sets in use at the time were unable to receive their channels. With the passage of the All-Channel Receiver Act in 1964, all new television sets were required to include a UHF tuner, nonetheless, it would still take a few years for UHF stations to become competitive. be457b7860
Uninstall License Manager Ansys
Undivided Rights: Women of Color Organizing for Reproductive Justice mobi download book
Hide IP Easy 5.5.7.8 with [Latest] Crack
The Outer Worlds on Nintendo Switch will arrive by early 2020