This consisted of the voltage regulation, 8085 (the brain), 8155 (the arms and legs), the EPROM and some other necessary peripherals required for the working of the system. The top board, as described above was the eye candy. It consisted of LEDs that would show the position of the current player, the number a player got on the dice and a few switches for controlling the game flow.
8085 Instruction Set Gaonkar
The programming had to be done by creating the binary from the assembly and then flashing it to an EPROM (yeah, the one you have to erase every time with a UV light). After numerous days of struggling with the 8085 simulator and many flashes of the code (and waiting for the code to be erased after ejecting the EPROM from the board and placing it in the UV eraser), it worked! We were able to satisfactorily play a few games of ludo, all that with an 8085.
The 8085 is supplied in a 40-pin DIP package. To maximise the functions on the available pins, the 8085 uses a multiplexed address/data (AD0-AD7) bus. However, an 8085 circuit requires an 8-bit address latch, so Intel manufactured several support chips with an address latch built in. These include the 8755, with an address latch, 2 KB of EPROM and 16 I/O pins, and the 8155 with 256 bytes of RAM, 22 I/O pins and a 14-bit programmable timer/counter. The multiplexed address/data bus reduced the number of PCB tracks between the 8085 and such memory and I/O chips.
Both the 8080 and the 8085 were eclipsed by the Zilog Z80 for desktop computers, which took over most of the CP/M computer market, as well as a share of the booming home-computer market in the early-to-mid-1980s.
The 8085 had a long life as a controller, no doubt thanks to its built-in serial I/O and five prioritized interrupts, arguably microcontroller-like features that the Z80 CPU did not have. Once designed into such products as the DECtape II controller and the VT102 video terminal in the late 1970s, the 8085 served for new production throughout the lifetime of those products. This was typically longer than the product life of desktop computers.
The 8085 is a conventional von Neumann design based on the Intel 8080. Unlike the 8080 it does not multiplex state signals onto the data bus, but the 8-bit data bus is instead multiplexed with the lower eight bits of the 16-bit address bus to limit the number of pins to 40. State signals are provided by dedicated bus control signal pins and two dedicated bus state ID pins named S0 and S1. Pin 40 is used for the power supply (+5 V) and pin 20 for ground. Pin 39 is used as the Hold pin. The processor was designed using nMOS circuitry, and the later "H" versions were implemented in Intel's enhanced nMOS process called HMOS II ("High-performance MOS"), originally developed for fast static RAM products.[3] Only a single 5-volt power supply is needed, like competing processors and unlike the 8080. The 8085 uses approximately 6,500 transistors.[4]
The 8085 incorporates the functions of the 8224 (clock generator) and the 8228 (system controller) on chip, increasing the level of integration. A downside compared to similar contemporary designs (such as the Z80) is the fact that the buses require demultiplexing; however, address latches in the Intel 8155, 8355, and 8755 memory chips allow a direct interface, so an 8085 along with these chips is almost a complete system.
The 8085 has extensions to support new interrupts, with three maskable vectored interrupts (RST 7.5, RST 6.5 and RST 5.5), one non-maskable interrupt (TRAP), and one externally serviced interrupt (INTR). Each of these five interrupts has a separate pin on the processor, a feature which permits simple systems to avoid the cost of a separate interrupt controller. The RST 7.5 interrupt is edge triggered (latched), while RST 5.5 and 6.5 are level-sensitive. All interrupts are enabled by the EI instruction and disabled by the DI instruction. In addition, the SIM (Set Interrupt Mask) and RIM (Read Interrupt Mask) instructions, the only instructions of the 8085 that are not from the 8080 design, allow each of the three maskable RST interrupts to be individually masked. All three are masked after a normal CPU reset. SIM and RIM also allow the global interrupt mask state and the three independent RST interrupt mask states to be read, the pending-interrupt states of those same three interrupts to be read, the RST 7.5 trigger-latch flip-flop to be reset (cancelling the pending interrupt without servicing it), and serial data to be sent and received via the SOD and SID pins, respectively, all under program control and independently of each other.
SIM and RIM each execute in four clock cycles (T states), making it possible to sample SID and/or toggle SOD considerably faster than it is possible to toggle or sample a signal via any I/O or memory-mapped port, e.g. one of the port of an 8155. (In this way, SID can be compared to the SO ["Set Overflow"] pin of the 6502 CPU contemporary to the 8085.)
Like the 8080, the 8085 can accommodate slower memories through externally generated wait states (pin 35, READY), and has provisions for Direct Memory Access (DMA) using HOLD and HLDA signals (pins 39 and 38). An improvement over the 8080 is that the 8085 can itself drive a piezoelectric crystal directly connected to it, and a built-in clock generator generates the internal high-amplitude two-phase clock signals at half the crystal frequency (a 6.14 MHz crystal would yield a 3.07 MHz clock, for instance). The internal clock is available on an output pin, to drive peripheral devices or other CPUs in lock-step synchrony with the CPU from which the signal is output. The 8085 can also be clocked by an external oscillator (making it feasible to use the 8085 in synchronous multi-processor systems using a system-wide common clock for all CPUs, or to synchronize the CPU to an external time reference such as that from a video source or a high-precision time reference).
The processor has seven 8-bit registers accessible to the programmer, named A, B, C, D, E, H, and L, where A is also known as the accumulator. The other six registers can be used as independent byte-registers or as three 16-bit register pairs, BC, DE, and HL (or B, D, H, as referred to in Intel documents), depending on the particular instruction. Some instructions use HL as a (limited) 16-bit accumulator. As in the 8080, the contents of the memory address pointed to by HL can be accessed as pseudo register M. It also has a 16-bit program counter and a 16-bit stack pointer to memory (replacing the 8008's internal stack). Instructions such as PUSH PSW, POP PSW affect the Program Status Word (accumulator and flags). The accumulator stores the results of arithmetic and logical operations, and the flags register bits (sign, zero, auxiliary carry, parity, and carry flags) are set or cleared according to the results of these operations. The sign flag is set if the result has a negative sign (i.e. it is set if bit 7 of the accumulator is set). The auxiliary or half carry flag is set if a carryover from bit 3 to bit 4 occurred. The parity flag is set to 1 if the parity (number of 1-bits) of the accumulator is even; if odd, it is cleared. The zero flag is set if the result of the operation was 0. Lastly, the carry flag is set if a carryover from bit 7 of the accumulator (the MSB) occurred.
As in many other 8-bit processors, all instructions are encoded in a single byte (including register-numbers, but excluding immediate data), for simplicity. Some of them are followed by one or two bytes of data, which can be an immediate operand, a memory address, or a port number. A NOP "no operation" instruction exists, but does not modify any of the registers or flags. Like larger processors, it has CALL and RET instructions for multi-level procedure calls and returns (which can be conditionally executed, like jumps) and instructions to save and restore any 16-bit register-pair on the machine stack. There are also eight one-byte call instructions (RST) for subroutines located at the fixed addresses 00h, 08h, 10h,...,38h. These are intended to be supplied by external hardware in order to invoke a corresponding interrupt-service routine, but are also often employed as fast system calls. One sophisticated instruction is XTHL, which is used for exchanging the register pair HL with the value stored at the address indicated by the stack pointer.
All two-operand 8-bit arithmetic and logical (ALU) operations work on the 8-bit accumulator (the A register). For two-operand 8-bit operations, the other operand can be either an immediate value, another 8-bit register, or a memory cell addressed by the 16-bit register pair HL. The only 8-bit ALU operations that can have a destination other than the accumulator are the unary incrementation or decrementation instructions, which can operate on any 8-bit register or on memory addressed by HL, as for two-operand 8-bit operations. Direct copying is supported between any two 8-bit registers and between any 8-bit register and an HL-addressed memory cell, using the MOV instruction. An immediate value can also be moved into any of the foregoing destinations, using the MVI instruction. Due to the regular encoding of the MOV instruction (using nearly a quarter of the entire opcode space) there are redundant codes to copy a register into itself (MOV B,B, for instance), which are of little use, except for delays.[nb 2] However, what would have been a copy from the HL-addressed cell into itself (i.e., MOV M,M) instead encodes the HLT instruction, halting execution until an external reset or unmasked interrupt occurs.[nb 3]
Although the 8085 is an 8-bit processor, it has some 16-bit operations. Any of the three 16-bit register pairs (BC, DE, HL or SP) can be loaded with an immediate 16-bit value (using LXI), incremented or decremented (using INX and DCX), or added to HL (using DAD). LHLD loads HL from directly addressed memory and SHLD stores HL likewise. The XCHG operation exchanges the values of HL and DE. Adding HL to itself performs a 16-bit arithmetical left shift with one instruction. The only 16-bit instruction that affects any flag is DAD (adding BC, DE, HL, or SP, to HL), which updates the carry flag to facilitate 24-bit or larger additions and left shifts. Adding the stack pointer to HL is useful for indexing variables in (recursive) stack frames. A stack frame can be allocated using DAD SP and SPHL, and a branch to a computed pointer can be done with PCHL. These abilities make it feasible to compile languages such as PL/M, Pascal, or C with 16-bit variables and produce 8085 machine code. Subtraction and bitwise logical operations on 16 bits is done in 8-bit steps. Operations that have to be implemented by program code (subroutine libraries) include comparisons of signed integers as well as multiplication and division.
38c6e68cf9