Mis web's

E-Mail:

Log de arranque Livebox Inventel (DV4210) Firm 5.03.2-sp

Log de arranque de Livebox, conectando por el puerto serie

Cuadro de texto

96432SDRAM16bit_5GX101201234Hardware version 0x8A BLUE5G.6
56+678ESA: 00:16:ae:5a:02:b8
WEP KEY : F15C51EA3CC60ACFC3B9A533B8
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
Ethernet eth0: MAC address 00:16:ae:5a:02:b8
IP: 10.7.58.112, Default server: 0.0.0.0
Hardware version 0x0A BLUE5G.6 WITHOUT_OPTION
Factory Settings Recovery Switch OFF High
Register : 17
 
RedBoot(tm) bootstrap and debug environment [ROM]
Non-certified release, version release-wanadoo-fr - built 16:25:10, Jun 20 2006
 
Platform: Blue_5g (MIPS32 4Kc)
Copyright (C) 2000, 2001, 2002, Red Hat, Inc.
 
RAM: 0x80000000-0x81000000, [0x80445fb0-0x80fe2000] available
FLASH: 0xbe400000 - 0xbec00000, 128 blocks of 0x00010000 bytes each.
== Executing boot script in 0.200 seconds - enter ^C twice to abort
RedBoot> fis load -b 0x80010000 -m cramfs -f Image user_fs
Partition is : 0xbe430000 - 0x720000
mlen : 0x3c9038
begin_tag : 0xbe7f9000, end : 0xbe7f9038
Verif OK
Looking for Image in cramfs user_fs partition
cramfs_load : b 0x80010000, c 0xBE430000, s 0x00720000, f Image
.............loaded 0x1900FC bytes
 
Return with root_try==0
RedBoot> exec -c "boot_loader=RedBoot root=1F01 mem=16M" 0x80010000
root_try == 0 : leave boot cmd alone
Now booting linux kernel:
 Base address 0x8000fc00 Entry 0x80010000
 Cmdline : boot_loader=RedBoot root=1F01 mem=16M hwversion=BLUE5G.6-WITHOUT_OPTION redbootversion="release-wanadoo-fr-Jun 20 2006-16:25:10"
arcs_cmdline: boot_loader=RedBoot root=1F01 mem=16M hwversion=BLUE5G.6-WITHOUT_OPTION redbootversion="release-wanadoo-fr-Jun 20 2006-16:25:10"
Boot loader : REDBOOT
@ prom init
CPU revision is: 00029107
Primary instruction cache 16kb, linesize 16 bytes (2 ways)
Primary data cache 8kb, linesize 16 bytes (2 ways)
Linux version 2.4.17 (bfo@bfo) (gcc version 3.2.2) #1 Wed Sep 14 13:37:26 CEST 2005
Determined physical RAM map:
 memory: 00fa0000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
zone(0): 4000 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: boot_loader=RedBoot root=1F01 mem=16M hwversion=BLUE5G.6-WITHOUT_OPTION redbootversion="release-wanadoo-fr-Jun 20 2006-16:25:10"
bcm_console_setup
Calibrating delay loop... 254.77 BogoMIPS
Memory: 13812k/16000k available (1429k kernel code, 2188k reserved, 96k data, 60k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
mpi: No Card is in the PCMCIA slot
PCI: Fixing up bus 0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
pty: 256 Unix98 ptys configured
brcmboard: brcm_board_init entry
New led 8, mask : 0x00000001
New led 0, mask : 0x00000002
New led 9, mask : 0x00000004
New led 6, mask : 0x00000008
New led 1, mask : 0x00000010
Module bcm63xx_cons.c v1.0
date: Sep 14 2005 time: 13:37:40 - FPERIPH:50000000
block: 64 slots per queue, batch=16
PPP generic driver version 2.4.1
DBW flash: probing 16-bit flash bus
Physically mapped flash: Probing for AMD compatible flash...
mfr_id 0x00000001, dev_id 0x0000227E, dev_id2 0x00002210, dev_id3 0x00002200
Found AMD AM29BDS643D
table[i] : mfr_id 0x00000001, dev_id 0x0000227E, dev_id2 0x00002202, dev_id3 0x00002200, long_dev_id 1
Found AMD AM29LV640MB
table[i] : mfr_id 0x00000001, dev_id 0x0000227E, dev_id2 0x00002210, dev_id3 0x00002200, long_dev_id 1
Found AMD AM29LV640MB
Physically mapped flash: Found 1 x 8MiB AMD AM29LV640MB at 0x0
mtd_info :
type 3, size 0x00800000, erasesize 0x00010000, name Physically mapped flash, index 0, numeraseregions 3
mtd_info->priv : amd_flash_private : device_type 2, interleave 1, numchips 1, chipshift 23<5> mymtd is : 80f52120
Support for extended flash memory size : 0x00800000 ; ONLY 64MBIT SUPPORT
RedBoot partition for 64MBit non aligned Flash
RedBoot partition for 64MBit non aligned Flash
RedBoot partition for 64MBit non aligned Flash
RedBoot partition for 64MBit non aligned Flash
RedBoot partition for 64MBit non aligned Flash
Using RedBoot partition definition
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00030000 : "RedBoot"
0x00030000-0x00750000 : "user_fs"
0x00750000-0x007f0000 : "jffs_system"
0x007f0000-0x007ff000 : "FIS directory"
0x007ff000-0x00800000 : "RedBoot config"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 1024)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Ebtables v2.0 registered<6>NET4: Ethernet Bridge 008 for NET4.0
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 60k freed
init started:  BusyBox v0.60.4 (2003) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
 
SYSINIT
 
INVENTEL version : v5.03.2-sp
 
Mounting proc filesystem ...
Mounting tmpfs filesystem ...
> NORMAL BOOT <
 
+ [ ! -e /etc/rc.d ]
+ /bin/rm -f /tmp/touch.test
+ /sbin/insmod prod_test.o
Using /lib/modules/prod_test.o
insmod: init_module: prod_test: Device or resource busy
+ [ 1 = 0 ]
+ [ mtd0 = mtd0 ]
+ cat /proc/mtd
+ grep jffs_system
+ sed -n s/\(mtd\)\(.*\):\(.\)*/\2/p
+ /bin/mount -t jffs2 -o rw /dev/mtdblock2 /mnt/jffs2/jffs2_3
+ /bin/rm -f /tmp/touch.test
+ /bin/touch /tmp/touch.test
+ [ ! -e /tmp/touch.test ]
+ /bin/rm -f /tmp/touch.test
+ [ -e /tmp/touch.test ]
+ [ ! -f /mnt/jffs2/jffs2_3/etc/issue ]
+ cat /mnt/jffs2/jffs2_3/etc/issue.bluedsl
+ grep version
+ x=INVENTEL version : v5.03.2-sp
+ echo x=INVENTEL version : v5.03.2-sp
x=INVENTEL version : v5.03.2-sp
+ cat /etc_ro_fs/issue.bluedsl
+ grep version
+ y=INVENTEL version : v5.03.2-sp
+ echo y=INVENTEL version : v5.03.2-sp
y=INVENTEL version : v5.03.2-sp
+ [ INVENTEL version : v5.03.2-sp = INVENTEL version : v5.03.2-sp ]
+ /bin/echo Up to date version ...
Up to date version ...
+ [ ! -f /mnt/jffs2/jffs2_3/etc/finished ]
+ exit 0
Mounting other filesystems ...
cp: /etc/crontab_root: No such file or directory
+ echo Switching to RUNLEVEL 1 ...
Switching to RUNLEVEL 1 ...
+ runlevel_manage 1
+ local previous
+ runlevel=1
+ [ -f /var/run/runlevel ]
+ previous=N
+ [ 1 = N ]
+ [ ! -f /etc/rc1.d/K* ]
+ continue
+ echo 1
+ echo 68
+ [ ! -f /etc/rc1.d/S05hardware ]
+ [ 1 != N ]
+ suffix=hardware
+ stop=/etc/rc1.d/K[0-9][0-9]hardware
+ previous_start=/etc/rcN.d/S[0-9][0-9]hardware
+ [ -f /etc/rcN.d/S[0-9][0-9]hardware ]
+ sh /etc/rc1.d/S05hardware start
Using /lib/modules/2.4.17/kernel/modulesrc/atmapi.o
atmapi: init_module entry 0xc00ad060  Sep 14 2005 13:40:08
Using /lib/modules/2.4.17/kernel/modulesrc/drivers/char/adsl/impl2/adsldd.o
adsl: adsl_init entry
Using /lib/modules/2.4.17/kernel/modulesrc/drivers/atm/impl1/blaa.o
blaadd: blaa_detect entry
Using /lib/modules/2.4.17/kernel/modulesrc/drivers/net/enet/impl2/bcm_enet.o
Resetting DSP and 2nd eth ..
GPIOio : 0xe9ffffc1
GPIOio : 0xe9fff181
bcm6348enet: bcmenet_module_init
bcm6348enet: bcm6348_net_probe
EnetInfo[1].ucPhyType = 3
EnetInfo[1].ucPhyAddress = 31
Broadcom BCM6348B0 Ethernet Network Device v0.1 Sep 14 2005 13:40:11 Internal PHY
bcm6348enet: bcm6348_init_dev
bcm6348enet: init_buffers
bcm6348enet: init_dma
bcm6348enet: init_emac
mii_AutoConfigure
BMCR : 0x3000
BMCR : 0x3100
mii_GetConfig
BCM6348_ENET: Auto-negotiation timed-out
BCM6348_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:07:3A:FF:FF:FF
Broadcom BCM6348B0 Ethernet Network Device v0.1 Sep 14 2005 13:40:11 External PHY
bcm6348enet: bcm6348_init_dev
bcm6348enet: init_buffers
bcm6348enet: init_dma
bcm6348enet: init_emac
BMCR : 0x3000
BMCR : 0x3100
BCM6348_ENETMAC2 : AutoConfiguration Start
mii_AutoConfigure
BMCR : 0x3100
BMCR : 0x3100
mii_GetConfig
BCM6348_ENET MAC2 : Auto-negotiation timed-out
BCM6348_ENET MAC2 : 10 MB Half-Duplex (assumed)
BCM6348_ENETMAC2 : Configuring for HALF-DPLX
eMiiConfig : 0x0000
eth1: MAC Address: 00:07:3A:FF:FF:FF
Using /lib/modules/2.4.17/kernel/modulesrc/drivers/net/usb/impl2/bcm_usb.o
USB MAC ADDRESS belongs to 00:16:AE:5A:02:BA
USB HOST MAC ADDRESS belongs to 00:16:AE:5A:02:BB
Broadcom BCM6348B0 USB Network Device v0.3
usb0: MAC Address: 00 16 AE 5A 02 BA
usb0: Host MAC Address: 00 16 AE 5A 02 BB
Using /lib/modules/2.4.17/kernel/modulesrc/drivers/net/wl/impl2/wl.o
PCI: Enabling device 00:01.0 (0004 -> 0006)
wl0: Broadcom BCM4318 802.11 Wireless Controller 3.91.7.0
insmod: no_console.o: no module by that name found
Using /lib/modules/switch.o
Switch module creating proc entry
Using /lib/modules/watchdog.o
Watchdog init Build:  Sep 14 2005  13:42:42
 
Usage: ledctrl led_name led_state
 
Supported led names:
Adsl
Wireless
Voip
SelfTest
Lan
Led1
Led2
Led3
Led4
Led5
All
 
Supported led states:
Off
On
BlinkOnce
SlowBlinkContinues
FastBlinkContinues
+ [ ! -f /etc/rc1.d/S10adsl ]
+ [ 1 != N ]
+ suffix=adsl
+ stop=/etc/rc1.d/K[0-9][0-9]adsl
+ previous_start=/etc/rcN.d/S[0-9][0-9]adsl
+ [ -f /etc/rcN.d/S[0-9][0-9]adsl ]
+ sh /etc/rc1.d/S10adsl start
adsl start ...
+ [ ! -f /etc/rc1.d/S20backlight ]
+ [ 1 != N ]
+ suffix=backlight
+ stop=/etc/rc1.d/K[0-9][0-9]backlight
+ previous_start=/etc/rcN.d/S[0-9][0-9]backlight
+ [ -f /etc/rcN.d/S[0-9][0-9]backlight ]
+ sh /etc/rc1.d/S20backlight start
Update Backlight state
Off
Advanced
Device open failed: Address family not supported by protocol
+ [ ! -f /etc/rc1.d/S30network ]
+ [ 1 != N ]
+ suffix=network
+ stop=/etc/rc1.d/K[0-9][0-9]network
+ previous_start=/etc/rcN.d/S[0-9][0-9]network
+ [ -f /etc/rcN.d/S[0-9][0-9]network ]
+ sh /etc/rc1.d/S30network start
BcmAdsl_Initialize=0xC00BC418, g_pFnNotifyCallback=0xC00D0B90
kerSysGetSdramSize : 0x00FE0000
AdslCoreHwReset: AdslOemDataAddr = 0xA0FE504C
kerSysGetSdramSize : 0x00FE0000
Local network configuration ...
Ethernet network configuration ...
eth0: bcm6348_net_open
eth0: bcm_set_multicast_list: 00001003
eth0: bcm_set_multicast_list: 00001003
eth0: bcm_set_multicast_list: 00001003
eth0: bcm_set_multicast_list: 00001003
eth1: bcm6348_net_open
eth1: bcm_set_multicast_list: 00001003
eth1: bcm_set_multicast_list: 00001003
eth1: bcm_set_multicast_list: 00001003
eth1: bcm_set_multicast_list: 00001003
Hostname configuration : WANADOO-02B8
device usb0 entered promiscuous mode
eth0: bcm_set_multicast_list: 00001103
device eth0 entered promiscuous mode
eth1: bcm_set_multicast_list: 00001103
device eth1 entered promiscuous mode
br0: port 3(eth1) entering listening state
br0: port 2(eth0) entering listening state
br0: port 1(usb0) entering listening state
+ [ ! -f /etc/rc1.d/S40http_server ]
+ [ 1 != N ]
+ suffix=http_server
+ stop=/etc/rc1.d/K[0-9][0-9]http_server
+ previous_start=/etc/rcN.d/S[0-9][0-9]http_server
+ [ -f /etc/rcN.d/S[0-9][0-9]http_server ]
+ sh /etc/rc1.d/S40http_server start
Websrv start ...
+ [ ! -f /etc/rc1.d/S50wl_bcm ]
+ [ 1 != N ]
+ suffix=wl_bcm
+ stop=/etc/rc1.d/K[0-9][0-9]wl_bcm
+ previous_start=/etc/rcN.d/S[0-9][0-9]wl_bcm
br0: port 3(eth1) entering learning state
br0: port 2(eth0) entering learning state
br0: port 1(usb0) entering learning state
+ [ -f /etc/rcN.d/S[0-9][0-9]wl_bcm ]
+ sh /etc/rc1.d/S50wl_bcm start
br0: port 3(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
br0: topology change detected, propagating
nas_wksp_alloc_workspace: allocated NAS workspace 4476 bytes
nas_wksp_parse_cmd_line: nwksp.port 34954
nas_wksp_parse_cmd_line: nwksp.pid /var/run/nas.pid
nas_wksp_parse_cmd_line: nwksp.lan br0
nas_wksp_parse_cmd_line: nas[0].interface wl0
nas_wksp_parse_cmd_line: nas[0].hwaddr 00:16:ce:86:11:2d
nas_wksp_parse_cmd_line: nas[0].psk F15C51EA3CC60ACFC3B9A533B8
nas_wksp_parse_cmd_line: nas[0].mode 4
nas_wksp_parse_cmd_line: nas[0].ssid ee
nas_wksp_parse_cmd_line: nas[0].wsec 3
nas_wksp_parse_cmd_line: nas[0].wep.index 2
nas_wksp_parse_cmd_line: nas[0].wep F15C51EA3CC60ACFC3B9A533B8
nas_wksp_parse_cmd_line: unknown option -A, ignored
nas_wksp_parse_cmd_line: nas[0].gtk.rekey 0
nas_wksp_parse_cmd_line: nas[0].ssn.timeout 0
nas_wksp_parse_cmd_line: nas[0].disable_preauth 1
nas_wksp_open_wpa: br0: opened wpa socket 5
nas_wksp_open_wpa: br0: opened preauth socket 6
nas_wpa_open: wl0: opened wpa socket 7
nas_wksp_open_eapol: br0: opened eapol socket 8
nas_eapol_open: wl0: opened eapol socket 9
nas_wksp_open_host: host: opened loopback socket 10
nas_set_key: wl0: index 0, flags 0, len 0
nas_set_key: wl0: index 1, flags 0, len 0
nas_set_key: wl0: index 2, flags 0, len 0
nas_set_key: wl0: index 3, flags 0, len 0
nas_set_key: wl0: index 1, flags 2, len 13
nas_set_key: wl0:  using 128 bit key algo
 
nas_wksp_dispatch_packet: br0: include wksp wpa socket 5 in fdset
nas_wksp_dispatch_packet: br0: include wksp eapol socket 8 in fdset
nas_wksp_dispatch_packet: br0 include wksp eapol preauth socket 6 in fdset
nas_wksp_dispatch_packet: host: include wksp host socket 10 in fdset
Setting SSID "ee"
device wl0 entered promiscuous mode
br0: port 4(wl0) entering listening state
+ [ ! -f /etc/rc1.d/S60dhcp_dns_server ]
+ [ 1 != N ]
+ suffix=dhcp_dns_server
+ stop=/etc/rc1.d/K[0-9][0-9]dhcp_dns_server
+ previous_start=/etc/rcN.d/S[0-9][0-9]dhcp_dns_server
+ [ -f /etc/rcN.d/S[0-9][0-9]dhcp_dns_server ]
+ sh /etc/rc1.d/S60dhcp_dns_server start
dnsmasq configured as dhcp server
dnsmasq start ( DNS / DHCP server ) ...
+ [ ! -f /etc/rc1.d/S60pair ]
+ [ 1 != N ]
br0: port 4(wl0) entering learning state
+ suffix=pair
+ stop=/etc/rc1.d/K[0-9][0-9]pair
+ previous_start=/etc/rcN.d/S[0-9][0-9]pair
+ [ -f /etc/rcN.d/S[0-9][0-9]pair ]
+ sh /etc/rc1.d/S60pair start
+ [ ! -f /etc/rc1.d/S60upnp ]
+ [ 1 != N ]
+ suffix=upnp
+ stop=/etc/rc1.d/K[0-9][0-9]upnp
+ previous_start=/etc/rcN.d/S[0-9][0-9]upnp
+ [ -f /etc/rcN.d/S[0-9][0-9]upnp ]
br0: port 4(wl0) entering forwarding state
br0: topology change detected, propagating
+ sh /etc/rc1.d/S60upnp start
Starting pairing manager
No ADSL, default: abc0
Update Backlight state
Off
Advanced
Upnp init ...
MyConfig in /etc/upnp.conf:
        Debug=0
        descDocName: gatedesc.xml
        xmlPath: /etc/linuxigd
        g_iptables: /usr/sbin/iptables
        g_forwardChainName: upnp
        g_preroutingChainName: upnp
        g_upstreamBitrate: 0
        g_downstreamBitrate: 0
 
 TGU: IpAddress: 192.168.1.200
+ [ ! -f /etc/rc1.d/S80bluetooth ]
+ [ 1 != N ]
+ suffix=bluetooth
+ stop=/etc/rc1.d/K[0-9][0-9]bluetooth
+ previous_start=/etc/rcN.d/S[0-9][0-9]bluetooth
+ [ -f /etc/rcN.d/S[0-9][0-9]bluetooth ]
+ sh /etc/rc1.d/S80bluetooth start
Device open failed: Address family not supported by protocol
Function cleanup_link_keys
wifi_nb : 0
0 link keys removed
/sbin/wlctl mac none
/sbin/wlctl kickall
wl0: Operation not supported
var     unrecognized name, type -h for help
 
/sbin/wlctl macmode 0
 INFO : IGD root device successfully registered.
Using /lib/modules/2.4.17/kernel/drivers/usb/usb-ohci.o
PCI: Enabling device 00:09.0 (0000 -> 0002)
usb-ohci.c: USB OHCI at membase 0xc015bb00, IRQ 20
usb-ohci.c: usb-00:09.0, PCI device 14e4:6300
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
Status : 0
Using scsi_mod.o
SCSI subsystem driver Revision: 1.00
Using sd_mod.o
Using usb-storage.o
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
Using nls.o
Using fat.o
Using vfat.o
 INFO : Advertisements Sent.  Listening for requests ...
mount: Mounting /dev/sda1 on /webs failed: No such device or address
telnetd: starting
  port: 23; login program: /bin/sh
Using /lib/modules/bt_reset.o
Bluetooth configuration ...
killall: hcid: no process killed
killall: hciattach: no process killed
killall: sdpd: no process killed
killall: dund: no process killed
killall: pand: no process killed
Using /lib/modules/bluez/bluez.o
BlueZ Core ver 2.4 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
Using /lib/modules/bluez/l2cap.o
BlueZ L2CAP ver 2.3 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
Using /lib/modules/bluez/rfcomm.o
BlueZ RFCOMM ver 1.1
Copyright (C) 2002 Maxim Krasnyansky <maxk@qualcomm.com>
Copyright (C) 2002 Marcel Holtmann <marcel@holtmann.org>
Using /lib/modules/bluez/bnep.o
BlueZ BNEP ver 1.2
Copyright (C) 2001,2002 Inventel Systemes
Written 2001,2002 by Clement Moreau <clement.moreau@inventel.fr>
Written 2001,2002 by David Libault <david.libault@inventel.fr>
Copyright (C) 2002 Maxim Krasnyanskiy <maxk@qualcomm.com>
Using /lib/modules/bluez/hci_uart.o
BlueZ HCI UART driver ver 2.1 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
Using /lib/modules/bluez/sco.o
BlueZ SCO ver 0.3 Copyright (C) 2000,2001 Qualcomm Inc
Written 2000,2001 by Maxim Krasnyansky <maxk@qualcomm.com>
choix canal com et Verification du boot\n
rmmod: tty_spi: No such file or directory
Using /lib/modules/tty_spi.o
usage: insmod tty_spi spi_cs=N
CS=0 date: Sep 14 2005 time: 13:42:42, speed 1
hardware version returned by bootloader: 0x31303032
Using /lib/modules/tty_spi.o
usage: insmod tty_spi spi_cs=N
CS=0 date: Sep 14 2005 time: 13:42:42, speed 2
Mode: bcsp
Hardware version: 0x31303032 - Software version: 0x33313537
Bluetooth is OFF in this configuration. Disable scan and exit.
+ [ ! -f /etc/rc1.d/S99printkoff ]
+ [ 1 != N ]
+ suffix=printkoff
+ stop=/etc/rc1.d/K[0-9][0-9]printkoff
+ previous_start=/etc/rcN.d/S[0-9][0-9]printkoff
+ [ -f /etc/rcN.d/S[0-9][0-9]printkoff ]
+ sh /etc/rc1.d/S99printkoff start
Setting printk off
+ rm -f /var/run/rc.pid
Sysinit done
 
Please press Enter to activate this console.
 
WANADOO-02B8 login: root
 
 
BusyBox v0.60.4 (2003) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
 
#


Comments