JABSCO BILGE PUMPS : JABSCO BILGE

JABSCO BILGE PUMPS : PUMP IT UP CHICAGO.

Jabsco Bilge Pumps


jabsco bilge pumps
    bilge pumps
  • (bilge pump) a pump to remove bilgewater
  • (Bilge pump) A mechanism for emptying the bilge of water. Since all wooden ships would leak to some degree, pumps were always in demand. Spray and waves would only add to how much water a ship took on.
  • (Bilge pump) electric pump that pumps out water from a boat. Usually connected to a float switch that makes it turn on automatically if too much water enters a boat compartment.
jabsco bilge pumps - Jabsco 36600-0000
Jabsco 36600-0000 Marine PAR Belt Drive Bilge Pump (475-GPH, 12-Volt, 15-Amp, 3/4")
Jabsco 36600-0000 Marine PAR Belt Drive Bilge Pump (475-GPH, 12-Volt, 15-Amp, 3/4")
36600 Diaphragm Bilge Pump475 usgph open flow outputSelf-priming up to 10ft vertical lift, allows mounting above wet bilgesDiaphragm design allows extended dry runningComplete with Pumpgardā„¢ strainerPermanently Lubricated Ball Bearings on Shaft and Connecting Rod

The Jabsco 36600-0000 Marine PAR Belt Drive Bilge Pump is self priming up to 10 feet of vertical lift, allows mounting above wet bilges. Featuring a 475 gallons per hour (1800 liters per hour) open flow output and quiet operation, the diaphragm design allows extended dry running. This pump also features a built-in hydraulic pulsation dampener and comes complete with a pumpgard strainer.
Jabsco's diaphragm bilge pumps are self-priming, so they can be mounted above and outside of harsh bilge environments. Because they are mounted remotely, the intake hose can be routed to the lowest point of the bilge regardless of space limitations. They are supplied with an in-line strainer to prevent damaging debris from entering pump. The reliable diaphragm design is not damaged by dry running.
Features:
Self-Priming
Diaphragm Design Allows Dry Running
Quiet Operation
Permanently Lubricated Ball Bearings on Shaft and Connecting Rod
Large Vibration Absorbing Pads
Corrosion Resistant Materials Throughout for Sea Water Service
Built-in Hydraulic Pulsation Dampener
Meets USCG Regulation 183.410 and ISO 8846 Marine for Ignition Protection
/
Specifications:
Body: Plastic
Port Type: 3/4" Hose barb
Voltage: 12
Weight: 11 pounds / 5 kg
Flow rate: Nominal 36 Liters/min (8 gallons/min)
Self-priming from dry up to 2.4m (7.8 feet)
About Jabsco
Jabsco is a worldwide leading manufacturer of products for the leisure marine market including water system, engine cooling pumps, searchlights, and marine waste systems. Jabsco also offers industrial pumps for hygienic applications, fluid transfer in chemical processing, laboratory, paint processing, plating, and construction. Jabsco is part of ITT's Marine & Leisure family of companies, which includes Rule, Flojet, HydroAir, Danforth, LVM, and Sudbury. This synergistic alliance joined the strengths, expertise, and resources of these companies, thereby guaranteeing the accelerated development and introduction of innovative and reliable products.

77% (11)
Bilge Pump
Bilge Pump
In which Bilge Pump perform a stupendous 'Natural Blonde'
Bilge Pump
Bilge Pump
In which Bilge Pump are seen during soundcheck

jabsco bilge pumps
jabsco bilge pumps
Jabsco 18660-0121 Marine Water Puppy Bilge/Sump Flexible Impeller Pump (380-GPH, 12-Volt, 15-Amp Non-CE, 1/2" NPT Ports)
The Jabsco Water Puppy pump is the standard in compact, low voltage DC, self-priming, motor driven pumps. Since the Water Puppy is self-priming, it can be located above the fluid source and installed in a convenient location, mounted in any position. Able to lift water up to 4 feet, the flexible impeller can pass small solids without damaging the pump, and it delivers up to 7 GPM at open flow. It is equipped with a improved high torque motor and a new pressure cast bronze body featuring a reusable O-ring type end cover seal. Ideal for bilge pumping, bait tank circulation, livewell aeration, and washdowns.

Comments