TPLinkRepeater - Configure and Setup your TP Link Repeater

Are you finding it challenging to set up your TP link repeater? If you want to run a hassle-free and smooth setup procedure via TPLinkRepeater, you must go through this blog until the end. Here we have given the straightforward and easy-to-follow steps to configure and setup the extender.

TP Link is a well-reputed global provider of reliable networking devices and accessories. It manufactures and supplies an extensuve range of devices to more than 170 countries. Ranked as the No.1 provider of Wi-Fi devices, TP link is currently serving billions of people all across the world. The only challenging part users have to go through while using these products is their setup. Therefore, to make it convenient for the users, we have provided the steps to get started with your TP Link repeater in this blog. Hence, you are just a few clicks away from experiencing an uninterrupted and smooth internet connection!

Here we have explained the steps to configure the extender via the WPS button. All the users are suggested to follow the below instructions to configure their TP Link Repeater:-

• First of all, you have to keep your extender near your main Wi-Fi router.

• After this, you should make sure that you have plugged the extender into a power outlet.

• In the next step, you have to press the WPS button located on your router. Then, you should immediately press the WPS button given on the TP Link Repeater.

• Note: all users are suggested to push the WPS button of the extender within two minutes of pressing the router’s WPS button.

• Once you've pushed the WPS button on your router, the WPS LED on the router must blink. In case the WPS LED doesn’t light up, you should push the button again until the LED light starts blinking. The same goes for the extender. If the WPS LED light of the extender does not blink, you should press the button again.

• The complete WPS procedure will last for about two minutes. Thus, all the users are suggested to wait for two minutes and check the wireless signal LED of your Range extender.

• If the light is on, it means that your Range extender has been connected to your primary router.

• Note: if you find the WPS LED light off even after two minutes, it indicates that the WPS extender configuration has failed. Thus, you have to repeat the steps mentioned above.

• Now, you have successfully configured your range extender and can keep it in a proper place where you need to boost or extend your internet signals.

All the users have to perform the TPLinkRepeater setup in order to get rid of the intermittent internet connectivity and enjoy a smooth internet network. Thus, all the users are suggested to go through and follow the below-given points to run TPLinkRepeater.net setup with no issues:-

• First of all, the users should plug their TP Link Extender into the wall power outlet.

• Note: the users should make sure that they have plugged their extender into the power outlet which is nearest to their primary router.

• Then, you should connect the TP Link range extender with your computer with an Ethernet cable.

• After this, you need to visit the official login page of the TP Link extender via “TPLinkRepeater” on your preferred internet browser.

• After this, you have to wait until the official page gets opened on the screen.

• Here, you should log in to your extender network.

• After successfully logging in to TpLinkReapeater, you will be redirected to the next page.

• On the new page, you should click on the “Quick Setup” option.

• Then, tap on the “Next” button.

• Here, the users will be asked to choose their region and location.

• After selecting your region, you should click on the “Next” button.

• Once you click on the Next button, your TP Link will start processing and scanning the wireless router network that you are using.

• Note: Now, the users have to select their wireless network from the available networks.

• After selecting your wireless network, you should click on the “Next” button.

• In the next step of the TpLinkRepeater.net setup, you will be asked to enter the login password of the wireless network.

• After entering the password, you should click on the “Next” option.

• In the next window, you should check the network settings.

• In the last step, all the users are suggested to click on the “Finish” button.

This blog includes the steps to configure and setup the TP Link Repeater via tplinkrepeater.net. All the instructions given in this blog are simple-to-follow, even for non-technical users. However, if you still face any issues, you must get in touch with their customer support.