1980 Kawasaki EFI/DFI Models

In 1980 Kawasaki took a departure from conventional motorcycle design and release two EFI based models, the z1000H and the z1000G.

1980 z1000H 

The z1000H was only released in 1980 and was sold in Europe, Australia, New Zealand and Africa (and maybe one or two other places). It was not released into the United States but some machines did find there way there. It came in Black with gold pin strips and the alloy wheels where gold with a polished rims. The bike is essentially a z1000 MkII motor with a different cylinder head featuring port injection. The throttle bodies only contained a butterfly valve and the choke mechanism. The reliability of the Digital Fuel Injection (DFI) system was questionable and many bikes found themselves being converted to carburettors very quickly. The success was short lived as neither model saw a second year.

1980 z1000G 

The 1980 z1000G was also referred to as the "z1 Classic" as this is what is stamped on the side covers. It Is an “Custom” style z1000 MkII with z1/z1a/z1b style side covers in a similar vein to the LTD’s that came before it but generally acknowledged as not as good. Cosmetically it had a very large seat, chrome grab rail, round tank (with chrome fitted plates) and pull back handle bars in the "custom" style of the era. The “G” model was released in the USA only.  Some have found there way to Australia and Europe.

Rebuilding/Restoring Possibilities

The "G" and "H" models are among the rarest of the Kawasaki line up and make an excellent bike if the EFI hardware is maintained or replaced by an aftermarket MegaSquirt System.

The “G” is an ideal restoration project back to factory specifications if you wish to seek the unusual style of the era. The “H” makes both an excellent factory restoration project but has plenty of scope to be rebuilt as a modern street fighter.

EFI System & Hardware

The EFI/DFI (Electronic Fuel injection / Digital Fuel injection) was adapted from an automotive system developed by either Datsun, Nissan or Bosch (no one can give a definitive answer) and was rebadged as "JECS". The Injectors are low impedance and pull a large current to snap open at high RPM. Today, high impedance injectors are available that have the same or better characteristics. The controller is obsolete and not user programmable. Almost any aftermarket system can be used to replace it, the Mega-Squirt (MS) would give the best bang for the buck and is fully programmable as well as a working track record on z650, z900’s and z1000’s.

Before considering conversion it is important to understand the design of the EFI in factory form. The original design uses an air flap to measure the air flow. This is clearly from a car design and is not suitable for a motorcycle due to the large overlap of the cams and the pressure wave issues inside the inlet ports. Possibly not know at the time by the engineers.

In addition to the Air Flap, the EFI system has 3 additional sensors. A sensor to measure the cylinder head temperature also known as Coolant Temperature (CLT), an Inlet Air Temperature sensor (IAT) and a Throttle Position Sensor (TPS).

The injectors are mounted onto the head (Port Injection) and fuel is delivered to the injectors via a common fuel rail that is under pressure from an electric fuel pump. The pressure is controlled via a vacuum control valve which derives its vacuum from the 2 and 3 inlet manifold rubbers. The fuel is returned to the petrol tank via a one way valve in the base of the tank opposite the tap. The fuel pump is controlled via a relay which is controlled via the EFI computer. The computer also measures the ignition pulse rate from the coil to determine engine RPM.

The system is quite simple but has no scope for user configuration hence it cannot be altered for different fuels and engine modifications. The EFI computer also has no O2 sensor support capability so self tuning and monitor of O2 emissions is not possible. The VE calculations for the engine must be precise in order for it to work correctly.

Replacing the EFI system

The EFI design now present on all modern vehicles is a vast refinement over the technology of 1980. EFI has evolved to meet the strict emission laws that carburettors could not ever hope to achieve. The factory standard EFI system from 1980 has too many deficiencies to cope in the modern world so replacing it with an aftermarket system is ideal. The following points use the Mega Squirt designed by Bruce Bowling and Al Grippo as the EFI computer:

Sensors (IAT & CLT)

The sensors could be used if you recalibrate the CPU to recognise the response curve of the sensor or just replace them with GM parts to gain both reliability and the default code is compiled to support them.

TPS

The TPS design has basically not changed, but I would be replacing the TPS with a modern unit and replace the connectors at the same time just to improve the reliability.

Air Flap.

Ditch the air flap, put it in a display case and use an automotive GM MAP sensor. The Mega Squirt (MS I) unit has a MAP sensor on board. The Micro Squirt scheduled for release in 2007 requires an external one. A GM MAP sensor from any modern car will do the job, just double check the pinouts and specs to be sure. You will need a restriction valve to dampen the air turbulence inside the inlet track.

Mounting

Use the same mounting point but allow for the ability to plug in a computer so you can do all kinds of neat things like data logging and tuning. The connector on the factory unit cannot be used, so you will need to remove t, see “Wiring” below.

Injectors

The standard injectors are low impedance (<2 ohms) so a flyback board is required, they are Bosch injectors made or sold under license at the time. You will not be able to buy originals so just use a modern equivalent. The exact flow rates are not documented but some calculations using an online calculator should yield the correct result. You might be looking at a 200cc/min injector. The pressure regulator wont change as the standard pressure is somewhere around 36-42 psi.

Wiring

You will need to change little of the wiring just connect it to the correct points on the new controller. The air flow wiring can be ignored unless an external MAP sensor is being used on a Micro Squirt. Double check the injector wiring, you may need to run an extra one to do bank firing as it may be a single fire (I cant remember but will check).

 Additional pictures are available at My z1000G Page

References:

Mega squirt web site:  http://www.msefi.com/

MS home Page: http://www.bgsoflex.com/megasquirt.html

Mega squirt manual: http://www.megamanual.com/v22manual/mtabcon.htm

Msextra: http://www.msextra.com/index.php