_text_

В другия раздел има инфо как се прави Jtag hack на конзола. При jasper дъна често има твърде много нечетими сектори в нанда. Ето как може да се оправят нещата за да не ви забива след глитчването и да замръзва в дашборд.

If you want to do it manually, you have to do this:
• Take the picture above as example.
• It says: Note : Block 0x2CE found at 0x3F8
• This is where the bad block 0x2CE was remapped.
• nandpro xbr.bin: -r16 block2ce.bin 2ce 1 (Reads block 0x02CE and saves as block2ce.bin)
• nandpro xbr.bin: -w16 block2ce.bin 3f8 1 (Write block2ce.bin to 0x3f8 where block is remapped)
• You will have to do this for each block.
• Here is the "formula":
• nandpro xbr.bin -r16 blockXXX.bin XXX 1 (Where XXX is the bad block number)
• nandpro xbr.bin -w16 blockXXX.bin YYY 1 (Where YYY is the address where block is found in degraded)
Tips on finding a xbox with an exploitable CB version

Това е хак на дашборда, тоест на софтуера управляващ дънната платка на конзолата. Може да се стратират игри от харддиск без наличен компакт диск. Всички игри както и допълнителни нива към тях DLC тръгват .

За четене и запис на NAND може да се ползва PLT кабел, 5 резисотра по 100 ома и един диод 1n 4148.




Fully compatible with all XBOX360 NAND models.
Fully compatible with NandPro2.0e Software and other third party software.
Easily reprogrammable with via LPT connector.
Quick reading and writing times.
Microchip based for enhanced stability

===========
Необходими евтини дреболии:
One Xilinx CoolRunner II CPLD XC2C64A Glitch Board aka C-Mod,

40pin Breakout Pin headers, if the board batch has no pin header pre soldered;
1K Resistor x1, 22K Resistor x1, 100nF 104 capacitor x2, 220pF 221 capacitor x2
One 40 PIN DIP IC Socket for the CPLD board, so you can solder to the socket instead of the board itself.
1N4148 switching diodes x 3
The chip contains no code/software/firmware, you can program it with the LPT interface Xilinx CPLD programmer or USB interface Xilinx CPLD programmer.
Wire type: Kynar 26AWG
270pF for slim


Команди за четене на нанда
For Xenon, Zephyr, Flacon, Opus and 16mb Jasper's(No internal memory)
C:\Nandpro20b\nandpro.exe lpt: -r16 nand1.bin
For Jasper's with 256mb Internal memory.
C:\Nandpro20b\nandpro.exe lpt: -r256 nand1.bin
For Jasper's with 512mb Internal memory.
C:\Nandpro20b\nandpro.exe lpt: -r512 nand1.bin
For Slim Trinity 4GB or 250 Gb Internal memory.
C:\Nandpro20b\nandpro.exe lpt: -r16 nand1.bin



В другия раздел има инфо как се прави Jtag hack на конзола. При jasper дъна често има твърде много нечетими сектори в нанда. Ето как може да се оправят нещата за да не ви забива след глитчването и да замръзва в дашборд.

Flash Config: 0x01198010
Block Size: 16KB Block Limits: 0x000000..0x0003FF
File: dump1.bin
Reading
Error: 250 reading block 161
03FF
----
remapped block 161 with:

nandpro dump1.bin: -r16 161.bin 3FF 1
nandpro dump1.bin: -w16 161.bin 161 1

I also erased the last part with:

nandpro dump1.bin: -r16 3FE.bin 3FE 1
nandpro dump1.bin: -w16 3FE.bin 3FF 1

family code reset
LT RT X Y LB RB "left d-pad" (hold left analog stick in) "right d-pad" x2
----------
Mine was LT, RT, X, Y, LB, RB, D-pad UP, A, X, A. It asked me if I wanted to reset settings when I correctly entered that combo.
----------------
LT RT X Y LB RB Y "Left Stick in" (press it in) Y Y

LT, RT, X, Y, LB, RB, Y, HOLD LEFT STICK IN AND I PUSHED X,X AND IT
-------------
its become like this: LT,RT,X,Y,LB,RB,X,X,UP,Down,Down,Down.....tell the window Popped up!!
-------------
UPDATE: LT,RT,X,Y,LB,RB,Down,Down,Down,Down.....tell the window Popped up!!!
---------------
LT RT X Y LB RB (D-Pad Up) Y Y X

(9,83A on 12V stated on the box) corona
On the back of my console it says 10.83A and the power supply that came with the xbox is a 9.6A power supply.